| 1. | The parasitic parameters of the encapsulated pin diode must be tuned because they do great harm to the switch performance
封装pin二极管的寄生参量对开关的性能影响很大，必须对寄生参量进行调谐。 |
| 2. | The traditional methods of parasitic parameter extraction in eda , which based on the concept of lumped component , have lost their accuracy
传统的eda设计中的基于集总电路概念的参数提取算法已经失去准确性。 |
| 3. | Because of the influence of some parasitic parameter in pin diode and circuits , some measure must be taken to compens ate the circuits
由于pin管和开关电路中存在一些寄生参量的影响，实际制作中可采取相应措施对电路进行补偿。 |
| 4. | The problem in high speed signal process , such as parasitic parameter and gate delay is also the difficulty hi the research
生成高速，稳定的时钟信号是本课题的目标。高速信号处理所遇到的常见问题，如寄生参数，门电路延迟是设计难点。 |
| 5. | Subsequently , we can get the chip s - parameter by adding the negative equipment circuit of the parasitic parameters in the s - parameter model of packaged device
之后，在有管壳封装器件的s参数模型中，加上负的寄生参量的等效电路，即可得到管芯的s参数。 |
| 6. | The macromodel is built up with the combination of device simulation and nonlinear curve fit , which makes the extraction of the substrate parasitic parameters more convenient and the circuit simulation more accurate
该宏模型通过器件模拟与非线性拟合相结合的方法建立，使衬底寄生参数的提取更加方便，同时保障了深亚微米电路特性的模拟精度。 |
| 7. | The difficulty in design microstrip pin sp3t switch is the via hole for grounding . we use both the radial parts and the via hole to get a good result . the fin - line pin switch is fully simulated using full - wave analysis , the parasitic parameter and the circuit assemble need to be considered
微带结构上过孔微波接地效果的不理想,是微带单刀三掷开关的难点,本文采用了扇形的微波接地和过孔直流接地结合起来,较好的解决了这一问题。 |
| 8. | 2 . the transmission line model of integrated inductors are presented and the procedure of extracting parasitic parameters of integrated inductors are induced to created an equation of parasitic parameters . a series of planar spiral integrated inductors are designed and fabricated
设计和制备了一组常规平面螺旋电感，并测量了其s参数，研究了电感量， q值的计算方法，计算了常规平面螺旋电感的各种参量，对实验结果进行了详细的分析和研究。 |
| 9. | These rules are based on the extraction of all parasitic parameters of the layout and device modeling , including transition behavior , high frequency characteristics of the different materials , and electrostatic couplings to printed circuit board ( pcb ) conductors and to the ground
这些规则是基于抽取pcb的敷线和器件模型的所有寄生参数而建立的，寄生参数的抽取考虑到了瞬态行为，不同材料的高频特性， pcb不同导体和各导体对地间的静电耦合。 |
| 10. | With soft - switching technology , inverter spot - welding power source has lower switching dissipation , lower electromagnetic interference and lower sensitivity to parasitic parameters of power circuit , contribute to inverter output characteristics and circuit efficiency , stability and reliability
采用软开关技术的点焊逆变电源，可减小开关损耗、电磁干扰及对电路寄生参数的敏感性，并从根本上改善电路的输出特性，提高电路的效率、稳定性和可靠性。 |
